Is your car your pride and joy, or are you ready for a change? Let us know and you could win a £300 John Lewis voucher | No thanks

F1 Style KERS For Volvo Road Cars

A light, cost-efficient and very eco-efficient solution that makes a four-cylinder engine feel like a six-cylinder, at the same time as reducing fuel consumption by up to 20 percent.

This autumn, Volvo Car Corporation will be one of the world's first car makers to test the potential of Kinetic Energy Recovery Systems on public roads.

The company has received a grant of 6.57 million Swedish kronor from the Swedish Energy Agency for developing next-generation technology for kinetic recovery of braking energy in a joint project together with Volvo Powertrain and SKF.

"Our aim is to develop a complete system for kinetic energy recovery. Tests in a Volvo car will get under way in the second half of 2011. This technology has the potential for reducing fuel consumption by up to 20 percent. What is more, it gives the driver an extra horsepower boost, giving a four-cylinder engine acceleration like a six-cylinder unit," relates Derek Crabb, Vice President VCC Powertrain Engineering.

60,000 revs per minute

The new system, known as Flywheel KERS (Kinetic Energy Recovery System), is fitted to the rear axle. During retardation, the braking energy causes the flywheel to spin at up to 60,000 revs per minute. When the car starts moving off again, the flywheel's rotation is transferred to the rear wheels via a specially designed transmission. The combustion engine that drives the front wheels is switched off as soon as the braking begins. The energy in the flywheel can be used to accelerate the vehicle when it is time to move off once again, or to power the vehicle once it reaches cruising speed.

"The flywheel's stored energy is sufficient to power the car for short periods. However, this has a major impact on fuel consumption. Our calculations indicate that the combustion engine will be able to be turned off about half the time when driving according to the official New European Driving Cycle," explains Derek Crabb.

Since the flywheel is activated by braking and the duration of the energy storage - that is to say the length of time the flywheel spins - is limited, the technology is at its most effective during driving featuring repeated stops and starts. In other words, the fuel savings will be greatest when driving in busy urban traffic as well as during active driving.

If the energy in the flywheel is combined with the combustion engine's full capacity, it will give the car an extra boost of 80 horsepower, and thanks to the swift torque build-up this translates into rapid acceleration, cutting 0 to 62 mph figures significantly.

Carbon fibre for a lightweight and compact solution Flywheel propulsion assistance was tested in a Volvo 240 back in the 1980s, and flywheels made of steel have been evaluated by various manufacturers in recent times. However, since a unit made of steel is large and heavy and has rather limited rotational capacity, this is not a viable alternative.

The flywheel that Volvo Car Corporation will use in its test car is made of carbon fibre. It weighs about six kilograms and has a diameter of 20 centimetres. The carbon fibre wheel spins in a vacuum to minimise frictional losses. "We are not the first manufacturer to test flywheel technology. But nobody else has applied it to the rear axle of a car fitted with a combustion engine driving the front wheels. If the tests and technical development go as planned, we expect cars with flywheel technology to reach the showrooms within a few years," says Derek Crabb.

He concludes: "The flywheel technology is relatively cheap. It can be used in a much larger volume of our cars than top-of-the-line technology such as the plug-in hybrid. This means that it has potential to play a major role in our CO2-cutting DRIVe Towards Zero strategy."

More at Volvo

Comments

Add a comment

 

Ask Honest John

Value my car

Amount to borrow
Sorry. The minimum loan amount is £1000
To pay back over

My credit score

Best available rate 9.20%

Total repayment £8,930.17

Total cost of credit £1,430.17

£186.05

48 monthly payments

Apply now

Representative example

Borrowing £7,500 over 4 years with a representative APR of 25.4%, an annual interest rate of 25.4% (Fixed) and a deposit of £0.00, the amount payable would be £239.77 per month, with a total cost of credit of £4,008.96 and a total amount payable of £11,508.96.

CarFinance 247 Limited is acting as an independent credit broker

Universal Square, Devonshire Street North, Manchester, M12 6JH